The application process of NatureOne® 100% Acrylic will vary with your project needs. Please refer to the following guidelines.

Preparation

CLEAN YOUR NON-WOOD SURFACE BEFORE STAINING – Refer to the General Preparation Guide.

Temperature And Moisture Specifications

NatureOne® 100% Acrylic products must be applied onto a clean, dry, substrate surface.

Temperature of surface and air must be between 50F and 90F.

1. Do Not apply a finish if temperature is expected to drop below 50F within 4 hours of application.
2. Do Not apply a finish in the direct sunlight, or when surface is hot to the touch, or the temperature is above 80F.

Moisture must not be present in the air, on the surface or the interior of the wood.

1. Do Not apply if the humidity level is high.
2. Do Not apply if rain is present or expected to be within 24 hours before or after your application.
3. Do Not apply when dew is present on the surface.
4. Do Not apply if the wood moisture content is above 18%.

Application Tools

1. A nylon polyester brush is the preferred tool for applying NatureOne®.
2. An airless sprayer can also be used. We recommend back brushing on all coats, to work the product into the wood and to even the pigmentation and film thickness. Spray Specifications:
   1. Tip Size 5-15 to 5-17 Keep the spray head no more than 12 inches from substrate.
   2. Pressure – 1000 to 1500 PSI
3. A stir stick for frequent mixing.

For Best Performance

Do a Color Check. Before applying your color selection onto your wood siding, perform test brush-outs onto a sample board of your wood species or discreet area of your siding, to verify your color outcome.

Thoroughly Stir the Stain. Pigments settle to the bottom of the container so it’s pertinent to thoroughly stir the product well at the beginning of your project and frequently during your application. Stirring distributes pigments throughout the product and helps to maintain a color consistency throughout your application.

“Box” Stains. (Mix contents of a new, full can of stain into the can of stain you’re currently staining from.) When the container of stain you are using is down to about ¼ full, fill it back up by adding stain from the next container of NatureOne® that you open. Thoroughly stir the newly opened container before combining into the ¼ full container. Then thoroughly stir the now combined stain and continue staining.

Apply Stain Liberally. Apply enough stain to saturate the wood pores, working it into the grain. Watch for dripping as you proceed. Immediately brush drips into the finish.

Apply Stain in the Direction of the Grain. Apply stain to three or four boards at a time, working all the way across the house. Work from the bottom up on initial application so drips are falling onto stained surface and are easier to brush in. On additional coats, work from the top of the house to the bottom, thereby always staining above the ladder.

Avoid Lap Marks. Brush product from the beginning of a board to the end of the board. Avoid lap marks by keeping your stop and start points wet and blended. Move your freshly dipped brush from the unstained section of wood, back into the existing wet stain to blend your stop and starting point.

Apply Caulking Where Necessary Before the Final Coat of Stain. Only Polyurethane or Latex caulks should be used with NatureOne®. DO NOT use a silicone caulk.

Application Procedures on Select Non-Wood Substrates, “Unfinished”

Composite and Fiber Cement Board Siding, Shake Panel Siding.

UNINSTALLED, Unfinished, substrate siding. Apply NatureOne® as a three-coat system, with back priming.

1. Apply One Coat of NatureOne® to all sides and ends of boards.
2. Allow to dry 2 to 4 hours.
3. Apply One Coat of NatureOne® to front side of boards.
4. Allow to dry 2 to 4 hours.
5. Apply One Coat of NatureOne® after boards are installed. Coated boards must “cure” at least 7 days before they can be stacked, or they will stick together.

INSTALLED, Unfinished, substrate siding. Apply NatureOne® as a three-coat system.

1. Apply One Coat of NatureOne®.
2. Allow to dry 2 to 4 hours.
3. Apply One Coat of NatureOne®.
4. Allow to dry 2 to 4 hours prior to applying an optional 3rd coat of NatureOne®.

Composite and Fiberglass Exterior Entry Doors, Garage Doors.

When possible, remove hinges, door hardware, and bottom door gasket prior to staining.

Apply NatureOne® as a three-coat system on Unfinished substrate doors.

1. Apply One Coat of NatureOne® to exterior and all edges.
2. Allow to dry 2 to 4 hours.
3. Apply One Coat of NatureOne® to exterior and all edges.
4. Allow to dry 2 to 4 hours.
5. Apply One Coat of NatureOne® to exterior and all edges.
6. Allow to dry 48 hours before replacing hardware and gasket, and before shutting door tightly.

Composite Exterior Railings and Spindles.

Apply NatureOne® as a three-coat system on Unfinished substrate railings and spindles.

1. Apply One Coat of NatureOne® to all sides and ends of the railings and spindles.
2. Allow to dry 2 to 4 hours before installing
3. Apply One Coat of NatureOne® to exterior and all edges.
4. Allow to dry 2 to 4 hours.
5. Apply One Coat of NatureOne® to exterior and all edges.

Composite Decking.

We do not recommend applying NatureOne® on composite decking. Most manufacturers of composite decking warn to never sand the surface, and sanding deck boards is required prior to applying NatureOne®.

Application Procedures on Select Non-Wood Substrates, “Primed” & Maintenance Application on Stained Select Non-Wood Substrates.

Composite and Fiber Cement Board Siding, Shake Panel Siding.

UNINSTALLED, Primed, substrate siding. Apply NatureOne® as a two or three-coat system.

1. Apply One Coat of NatureOne®.
2. Allow to dry 2 to 4 hours.
3. Install siding.
4. Apply One Coat of NatureOne® to front side of boards.
5. Allow to dry 2 to 4 hours before applying Optional 3rd coat of NatureOne®. Coated boards must “cure” at least 7 days before they can be stacked, or they will stick together.

INSTALLED, Primed, substrate siding. Apply NatureOne® as a three-coat system.

1. Apply One Coat of NatureOne®.
2. Allow to dry 2 to 4 hours.
3. Apply One Coat of NatureOne®.
4. Allow to dry 2 to 4 hours before applying Optional 3rd coat of NatureOne® .

Composite and Fiberglass Exterior Entry Doors, Garage Doors.

When possible, remove hinges, door hardware, and bottom door gasket prior to staining.

Apply NatureOne® as a two or three-coat system on Primed substrate doors.

1. Apply One Coat of NatureOne® to exterior and all edges.
2. Allow to dry 2 to 4 hours.
3. Apply One Coat of NatureOne® to exterior and all edges.
4. Allow to dry 2 to 4 hours before applying Optional 3rd coat of NatureOne® .
5. Allow to dry 48 hours before replacing hardware and gasket, and before shutting door tightly.

Composite Exterior Railings and Spindles.

Apply NatureOne® as a two or three-coat system on Primed substrate furniture.

1. Apply One Coat of NatureOne® to all sides and ends of the furniture.
2. Allow to dry 2 to 4 hours.
3. Apply One Coat of NatureOne® to all sides and ends of the furniture.
4. Allow to dry 2 to 4 hours before applying Optional 3rd coat of NatureOne® .

Composite Decking.

We do not recommend applying NatureOne® on composite decking. Most manufacturers of composite decking warn to never sand the surface, and sanding deck boards is required prior to applying NatureOne®.

Helpful Tips

Apply a finish to a vertical surface (siding, doors, railings) within 14 days of cleaning. Complete additional applications within 14 days of each other. If more than 14 days lapse between applications, you should reclean your surface, following the mild detergent cleaning guidelines.

Coating the back side of the board (Back-priming) is recommended prior to the siding installation. This will help control the absorption of excessive moisture and heat into the wood, which is sometimes produced from foil faced or ridged foam insulation, or moisture proof house wrap.

Caulking around windows, doors, etc. before applying the third coat will enhance the performance of the coating.

Clean Up

Clean up spills and spatters immediately with soap and water.

Clean tools immediately after use with soap and water.

Remove hardened stain buildup, at the ferrule, by soaking brush in a 50/50 mixture of simple Green concentrate and water.

Dispose of empty cans or unused contents in accordance with state and federal regulations.

Limited Warranty: The information and suggestions for preparation made herein are based on research and experience of Structures Wood Care, Inc., and are believed to be reliable. Application and surface conditions are beyond Structures Wood Care, Inc.’s control. Liability, if any, is limited to replacement of product or refund of its purchase price at Structures Wood Care’s option. Proof of purchase is required. Labor or cost of labor is excluded. Buyers must determine for themselves, by preliminary tests or otherwise, the suitability of the products for their purposes.